Order by phone... 1-866-278-6653 / 1-908-273-5401

Baby Casting | Page 1

Face Casting Examples  

ArtMolds Lifecasting Series

The Art of Baby Casting

The casting of a baby's hand, feet or bottoms is perhaps the first interest of the beginning life casting enthusiast. Creating these tiny molds doesn't require any particular experience and are often perfected on the first try. So they are a good place to start for anyone interested in life casting. In addition, the material requirements are both minimal and inexpensive. The only valuable item in the process is of course, the baby itself. But the materials involved are extremely safe to use on baby's delicate skin as they are hypoallergenic, having been made from such organic compounds as seaweed. Similar material to those used for those expensive spa facials.

Many agree that one of the most precious forms of life casting art one can create, are castings of babies and young children. They are emotionally powerful presents for grandparents as well as great keepsakes for friends and family. Over the years I nave never tired of the reactions that this tiny casting produces, from expressions of jaw dropping joy to copious tears. Yet not everyone appreciates these cute memorials. Years ago, I had the bright idea of taking a casting of a baby’s hand, posed in a tiny fist and then creating a series of silicone mold copies so that I could produce a number of duplicate castings of the little hand. Over a period of several days I cast 500 babies’ hands in polyurethane resin – a plastic. I then printed our company name and address on them so I could pass them out at the National Art Materials’ trade show as a souvenir. Though they were mostly very well received by the visitors to our booth, about ten percent of those that were offered the souvenirs actually ran from them – it gave them shivers. At first it surprised me. Then I realized that not everyone thinks of a detached baby’s hand as cute. Some think it is macabre. So let’s hope that your client or grandparent doesn’t think that way, too.


Figure 2. A table is readied with all the mold making materials needed for the casting process. See the list on the right.


Molding Materials:

(1) 16-OZ Dixe cup

Measuring cup

2- Mixing bowls or containers

Wire kitchen whisk

Box cutter or X-Acto knife

½ Lb Holywood Impression SIFREE alginate (Fast Setting)

Distilled water

1 –lb of CastRite of casting plaster


The materials to cast a new born of child's hand are extremely safe to use on even a newborn. We formulated our Hollywood Impressions alginate to be environmentally friendly, hypoallergenic and of course skin-safe. This material is basically made from seaweed and pulverized paper. To make a mold of a youngster, you need a very fast setting alginate, as you probably know, babies and toddlers can’t stay still and wait for your mold material to set. So if you use 80o-90 o F., water with Hollywood Impressions alginate, you will have a set time of a little less than two minutes. That is still too long, but with mixing and readying the alginate, you’ll cut off another 45-60 seconds, leaving a window of a minute – but, again that may be a bit too long to have your tiny subject to wait. So we advise waiting thirty seconds after you finish mixing before using it on the subject.

With that bit of a preamble under our belt, we begin the mold making process by first preparing a mold making container. We normally use a 16 Oz Dixie cup which we cut about halfway to two-thirds up from the bottom using a box cutter or an X-Acto knife. 

This makes the cup shallow enough to create a mold of the baby's hand, plus also capture some of the arm above the wrist. Of course the mold cup depth will vary based on the size of your  subject’s hand and arm. You can quickly determine the depth by placing the baby’s hand into the empty cup, making certain it doesn’t touch the bottom and then marking the spot on the side of the cup where you will cut.



Cutting a container

Figure 3. A 16-OZ cup is made more shallow to accept the babies hand to a little bit over the wrist.

With the mold container prepared, fill it with 80 o--90o F water (26.6 o--32.2o C) to the top of the cup. That is the amount of water you will need to mix with the molding powder.


Cutting a container

Figure 4 Warm water (distilled) is poured into the container to the top.

Page 1 | 2 | 3| 4